Skip to content
Home/Blog/Solar-powered traffic signals: how the parts fit together

Solar-powered traffic signals: how the parts fit together

A solar-powered flasher or signal head runs without a mains connection. It is built from four parts: a solar panel, a charge controller, a battery and the lamp they power. This page describes each part and how they connect, using the figures on our own product pages.

Where solar power is used

Solar systems are used at work sites where supplying power is difficult or impossible. Solar flashers are the most common product of this kind on motorways; solar variable message signs, solar-powered traffic signals and solar road studs are other uses.

The four parts

Sunlight reaches the panel. The panel feeds the charge controller. The charge controller charges the battery and supplies the lamp from it, and switches charging and the lamp off at set limits.

Solar panel

The panel is a current source that changes with the hours of sunshine and the angle of the sun. A panel sold as "12 V" delivers 16–20 V, so it is not connected straight to the battery; it connects through a charge controller.

Panel sizes on our pages: 5–10 W on the Q100 flasher (6 V, 5 Ah battery), 10 W on the MPPT double flasher, 20 W on the GPS-synchronised Q300.

Charge controller

The controller conditions the panel's output to suit the battery and keeps the battery from being overcharged or drained too far. The simplest controllers switch the panel on and off with a relay or MOSFET at a set voltage; PWM and MPPT controllers regulate the charge instead. Our post Solar Charge Controller Basics describes MPPT as drawing up to 30% more energy from the panel than PWM, with a conversion efficiency of 94–98%.

On our flashers: the Q300 and Q200 charge with PWM, MPPT optional; the Q100 charges with PWM; the MPPT double flasher charges at constant current or constant voltage and tracks the panel's maximum power point. All list overcharge and over-discharge protection; the GPS-synchronised Q300 and the MPPT double flasher close the output when battery voltage falls below 11.5 V.

Battery

The Q300 and Q200 take a 12 V, 7–22 Ah VRLA battery or an 11.1 V Li-ion battery; the Q100 uses 6 V, 5 Ah; the MPPT double flasher 12 V, 7 or 18 Ah; the GPS-synchronised Q300 12 V, 7 or 20 Ah.

With lead-based batteries, using more than 30–50% of the nominal capacity shortens their life — in practice 6–10 Ah of a 20 Ah battery. A lithium-ion battery can use its full capacity because its control circuit prevents over-discharge. A 300 mm housing holds a battery of at most 24 Ah, upright (Solar Flashers with Lithium-Ion Batteries). A Li-ion cell has a nominal voltage of 3.6–3.7 V and works between 2.5 V and 4.2 V (Li-Ion, Li-Po and LiFePO4 Batteries).

Lamp

The lamp is a group of LEDs behind a polycarbonate lens: red, yellow or green, 5 mm or 10 mm. It flashes at 500 ms on/off or at a selected speed, and an optional mode runs it at night only. Consumption is under 10 W on the Q300 and under 4 W on the MPPT double flasher.

The GPS-synchronised Q300 keeps flashers in step through GPS, with no master unit, so one unit failing or losing contact does not break the synchronisation of the others. It has eight operating scenarios, selected by a button, and nine brightness levels.

Running through low-sun periods

A solar system is sized in this order: total consumption; the minimum battery from the longest period without charging; then the panel from the region's average hours of sunshine. A flasher has to run 24 hours a day, 365 days a year on the yearly average, not only in sunny weather (Solar Power Systems).

With its panel disconnected, the GPS-synchronised Q300 on a fully charged 20 Ah battery runs at least 20 days in 24-hour mode; the MPPT double flasher on 18 Ah, at least 35 days.

Standard and ratings

TS EN 12352 covers warning and safety light devices used in road traffic; EN 12352 sets dimming requirements for solar flashers. The Sarix Q300 and Q100 solar flashers received TS EN 12352 certification (First TS EN 12352 Certification in Türkiye); the Q200, MPPT double and GPS-synchronised flashers list TS EN 12352 in their specifications.

The Q300, Q200, Q100 and MPPT double flashers operate from −40 °C to +70 °C; the GPS-synchronised Q300 from −30 °C to +70 °C. The Q300 and Q200 pages list a 5-year warranty. Our certificates are on the Quality Certificates page.

Products on this page