Skip to content
Home/Blog/How an intersection controller works: signal groups, MMU and NTCIP

How an intersection controller works: signal groups, MMU and NTCIP

An intersection controller is the device in the roadside cabinet that switches a junction's traffic lights. It runs the signal plan, reads the detectors, checks that no two conflicting directions get green together and reports to a central system. This post explains those parts one by one, using the figures on our own product pages for the ANTRA intersection controllers.

What an intersection controller does

The controller holds the junction's signal plan and switches each signal head on and off in the order and for the times the plan sets. The ANTRA G-Series has four operating modes.

  • Fixed-time: time-of-day plans with calendar overrides, for junctions with stable traffic patterns.
  • Vehicle-actuated: loop, radar, video or push-button detection extends a phase or ends it early when no more vehicles arrive (gap-out).
  • Coordinated: offset, cycle and split are synchronised along a corridor through ROTA, which is how a green wave is set up.
  • Adaptive: the plan is adjusted in real time from the detected demand, with GPS time synchronisation. This mode is described on the Adaptive Intersection Control System page.

Signal groups and phases

A signal group output is the physical output that drives a signal head. A phase is a timed block in which one or more compatible signal groups are switched on together. A through-and-right phase, for example, may drive a main signal head and two repeater heads: three group outputs commanded by one phase. The software can hold far more phases than the hardware has group outputs.

The G-Series is named after its number of signal group outputs. One hardware and firmware platform comes in nine configurations:

  • ANTRA-G4: 4 group outputs, 2 vehicle and 2 pedestrian phases, for pedestrian crossings and simple junctions.
  • ANTRA-G8: 8 group outputs, 4 vehicle and 4 pedestrian phases, for 3-arm T-junctions.
  • ANTRA-G12: 12 group outputs, 6 vehicle and 6 pedestrian phases, for T-junctions with a central island.
  • ANTRA-G16: 16 group outputs, 8 vehicle and 8 pedestrian phases, for 4-arm intersections.
  • ANTRA-G20: 20 group outputs, 12 vehicle and 8 pedestrian phases, for large 4-arm intersections.
  • ANTRA-G24: 24 group outputs, 16 vehicle and 8 pedestrian phases, for 4-arm intersections with a central island.
  • ANTRA-G28: 28 group outputs, 16 vehicle and 8 pedestrian phases, for central-island 4-arm intersections with early exit, plus 8 flashing outputs.
  • ANTRA-G32: 32 group outputs, 16 vehicle and 8 pedestrian phases, for pedestrian-protected large junctions, plus 8 flashing outputs and 4 single modules.
  • ANTRA-G64: 64 group outputs.

The output card measures the current on every channel. That is how a missing lamp, an overload or a short circuit is detected.

The MMU: an independent conflict monitor

MMU stands for Malfunction Management Unit. It checks every output against a conflict matrix, a table of the signal groups that must never show green at the same time. In ANTRA the MMU has its own power line, its own reset and its own clock, separate from the main processor (CPU). The CPU runs the controller program and the MMU runs the safety logic, so a software lock-up on the CPU cannot bypass the conflict matrix.

When the MMU detects a conflict or a fault, it opens a master cut-off relay that removes power from the whole output card.

The faults detected and reported are: mains voltage and frequency excursions; DC supply anomalies; over- or under-current on a group output (missing lamp, overload); short and open circuits; fuse failure; load-switch failure; output, detector or power card failure; conflict violations (green–green, green–yellow, yellow clearance); loop detector failed or healthy status; cabinet door open, power lost and restored, and red-lamp violations.

EN 50556 and EN 12675

EN 50556 is the European standard for road traffic signal systems, and EN 12675 sets the functional safety requirements for traffic signal controllers. The ANTRA brochure lists the independent MMU against both standards. The same compliance list includes EN 50293 for electromagnetic compatibility, IEC 60529 for the IP66 ingress rating and IEC 62262 for the IK10 impact rating.

NTCIP 1201, NTCIP 1202 and SNMPv3

NTCIP is a family of open communication standards for traffic equipment. NTCIP 1201 defines the global objects every device shares, such as time and scheduling; NTCIP 1202 defines the objects of an actuated signal controller. ANTRA supports NTCIP 1202 v03.19 and v04, NTCIP 1201 with the v04 scheduling table, and UG405:2008 for SCOOT systems.

The controller connects to the central software directly over the NTCIP stack, with no gateway and no proprietary protocol in between. SNMPv3 secures the connection with USM authentication and VACM access control. User accounts are role-based, firmware updates are signed, operator actions are logged, and security patches are provided for at least ten years from delivery.

Every fault event is stored in the controller and reported through the NTCIP 1202 blockEventLog object, so it appears in any management software that reads NTCIP. Our own central system is ROTA: it shows phase states, detector data and faults across the network, includes a MIB browser for reading NTCIP parameters directly, and analyses coordination, split failures and timing at corridor level. ROTA also manages controllers from other manufacturers that expose a standard NTCIP MIB.

Network connections: Ethernet 100 Mbit/s with VLAN segmentation, a 4G/LTE modem with SIM as primary or failover link, Wi-Fi for service access, RS-232 and RS-485 serial ports, GPS time synchronisation with NTP, USB Type-C for local configuration, and a built-in web interface for service and diagnostics.

Central-system work on our controllers goes back to the earlier ATG/06-AG controller, whose central system compatibility was completed and tested by our R&D team.

Field-replaceable cards and the IP66 / IK10 cabinet

ANTRA is built from separate cards on a Eurocard 3U backplane:

  • CPU: Linux LTS, 4 GB RAM, 32 GB storage, hardware watchdog, real-time clock and an 18650 Li-ion power-loss buffer.
  • MMU: independent safety monitor with the conflict matrix and the master cut-off.
  • Communication: Ethernet, 4G/LTE, Wi-Fi, GPS, RS-232/485 and USB-C.
  • Output: up to 64 signal groups at 120 or 230 VAC, with per-channel current monitoring.
  • Detector: up to 64 inputs for loops, push-buttons and dry contacts, plus Modbus and SNMP devices.
  • Power: 0.3 A device and 0.03 A personnel residual current devices, a 20 A EMI/RFI filter and a 40 kA surge arrester.

A failed card is replaced in the field without replacing the controller and without losing its configuration. All cards are reached from the front.

The cabinet is 2 mm galvanised steel with conformal-coated electronics, rated IP66 for ingress and IK10 for impact. It has an internal fan and heater, works from −40 °C to +70 °C, and a door-open sensor reports to the central system as an NTCIP alarm. Inside are one mains and one UPS-fed socket, a grounding busbar, and base extensions of 15 cm or 25 cm for cable management.

Where the ANTRA ranges differ

Our product pages list three ANTRA controllers.

  • ANTRA: lamp-failure detection, police control, detector inputs and green-wave coordination are built in; GPS and internet keep date, time and daylight saving correct.
  • ANTRA+: adds a built-in UPS and voltage regulator, so the junction keeps running through power cuts, voltage swings and unstable mains frequency. The catalogue lists an inverter power of 1,000–10,000 W and a battery supply time of more than 8 hours.
  • ANTRA Pi All-in-One: the controller in a single body, with IP65 protection. It received TS EN 50556, TS HD 638 S1, TS EN 12675 and TS EN 50293 certification.

Where a junction already has a working controller from another make, the Controller Retrofit module keeps the existing cabinet and field wiring, and adds NTCIP, V2X and an independent 300 ms safety cut on conflict.

Products on this page

Related posts: Phantom Effect in Traffic Signals · The Effects of Power Factor and Harmonic Distortion on the Traffic Signalling System · TCXO, Crystal Oscillators and GPS