Adaptive traffic signal control is a way of running traffic signals in which green and cycle times are calculated from the traffic measured on each approach, rather than taken from a fixed timetable. The controller reads its detectors, recalculates the signal plan within limits set by the traffic engineer, and repeats the calculation throughout the day.
Adaptive is one of four modes a controller runs. Using the ANTRA intersection controller as the example, this post goes through all four modes, the parts of the system, what published studies report and when a fixed-time plan is enough. The solution as a whole is described on the adaptive intersection control page.
Four modes
Which mode an intersection uses is set per site and per hour. Each line below is the definition used in our product documents.
- Fixed-time: time-of-day plan switching with calendar overrides, for stable and predictable patterns
- Vehicle-actuated: loop, radar, video or push-button detection extends or ends the green, with gap-out logic
- Coordinated: corridor-level offset, cycle and split synchronisation; green wave through the central layer
- Adaptive: GPS-synchronised real-time plan adjustment from detected demand
Fixed-time
The controller runs one of the plans prepared for the time of day. Calendar overrides can be defined for holidays or special days. The controller does not read the traffic at the junction; the plan rests on the assumption that traffic is regular.
Vehicle-actuated
Each approach can have loops, radar, video or push-buttons. These report to the controller's detector inputs, of which there are up to 64, plus 8 dedicated push-button inputs. Detection extends or ends the green; the green continues as long as the gap between vehicles stays under a set time. The decision is made inside the intersection itself. The difference between a virtual loop and an induction loop is covered in this post.
Coordinated
Successive intersections are considered together. Offset, cycle and split are synchronised at corridor level. The green wave is built and monitored in this mode, through the central layer; the controller does not wait for the centre to decide each green.
Adaptive
The adaptive mode adjusts the plan in real time from detected demand, GPS-synchronised. The plan is not a fixed timetable but the result of what is measured at that moment.
The control loop, step by step
- Observe: cameras, radar, loops and push-buttons report live vehicle and pedestrian demand.
- Interpret: the controller weighs that demand against the signal plan, minimum greens, clearance times and conflicts.
- Decide: it extends, ends, calls or skips phases, locally, without waiting for the centre.
- Control: monitored outputs drive the signal heads, and every channel is watched for faults.
- Measure: the central layer records phases, plan changes and performance.
What reads what
- Detection: loops, radar, video and push-buttons on each approach
- ANTRA controller: the signal program, the phase sequence and the independent safety unit
- Signal heads: driven from the group outputs, with per-channel current monitoring
- Central management: corridor coordination, fault reporting and performance records
The controller comes as the G-Series, with 4 to 64 signal group outputs; all of them are one hardware and firmware platform.
Priority requests
Emergency vehicle priority and public transport priority are optional modules on the same platform. A request from an approaching emergency vehicle or a late bus takes effect inside the signal plan, and the safety intervals are kept. The public transport priority page describes how a request reaches the intersection.
The safety unit does not change with the mode
In whichever mode, the independent MMU (Malfunction Management Unit) runs separately from the controller's processor, with its own power line, clock and reset. If it detects a conflict, it cuts power to the whole output card through the master cut-off relay. More in the intersection controller post.
Where the decision is made
The controller runs its signal program and its detection locally. The central layer coordinates corridors and records performance; it is not in the loop that decides each green. Where a junction has another brand of controller, the controller retrofit solution can bring a fixed-time junction into adaptive control and corridor coordination.
What published studies report
Our product documents contain no measured improvement result for adaptive mode. The figures below are not measurements at our installations; they come from published sources:
- The US Federal Highway Administration (FHWA) reports that adaptive signal control improves travel time by more than 10 percent on average, and by 50 percent or more where the existing signal timing is particularly outdated (FHWA: Adaptive Signal Control Technology).
- A study of single intersections (Stewart, Lepik and Van Aerde, Transportation Research Record 1692, 1999) found that adaptive strategies performed better than a fixed-time plan set only for average demand; that well-designed time-of-day plans performed better than both when traffic matched what the plans expected; and that the benefit grew as demand became more peaked (TRR 1692).
Results measured at our own installations will be added to this post when they are available.
When a fixed-time plan is enough
Read together, the two sources show where each mode fits:
- Fixed-time or time-of-day plans: traffic that repeats predictably from day to day, with plans that are reviewed and kept up to date.
- Adaptive control: demand that changes irregularly, such as events, incidents, roadworks or seasonal traffic, or timing plans that have not been revised for years.
Adding adaptive control to an existing intersection
Signal heads and poles usually stay in place. Three things are added or replaced:
- Detection on every approach: radar and cameras are mounted above the road; inductive loops need saw cuts in the road surface.
- A controller that runs adaptive mode. The ANTRA G-Series comes in versions from 4 to 64 signal group outputs.
- A communication link to the central layer over NTCIP 1202. Where another manufacturer's controller stays in the cabinet, the controller retrofit solution connects it.
Frequently asked questions
What is the difference between vehicle-actuated and adaptive control?
Vehicle-actuated control extends or ends individual greens inside a fixed plan structure. Adaptive control recalculates the plan itself, including cycle length, green split and offsets, and can do so for a group of intersections together.
Does adaptive control work at a single intersection?
Yes. At a single intersection it adjusts the cycle and the green split. Offsets and green waves need neighbouring intersections connected through the central layer.
Is an adaptive signal the same as a smart traffic light?
"Smart traffic light" is not a technical term; it is used for vehicle-actuated signals, adaptive signals and signals with countdown displays alike. Adaptive control specifically means that the signal plan is recalculated from measured demand.
What happens when a detector fails?
The controller reports the detector fault, and a fixed-time plan covers that approach until the detector is repaired.
Which detection does adaptive control use?
Inductive loops, radar, video and pedestrian push-buttons. They can be combined at one intersection; each reports to the controller's detector inputs. Camera-based detection is compared with loops in the virtual loops post.